A modern blanket ladder from dried cedar poles

A modern blanket ladder can turn two dried cedar poles into a useful feature for a hallway, verandah or studio. Its upright silhouette provides a convenient place for throws and quilts, while the construction must still resist tipping, joint movement and the daily pull of heavy fabric.

Timber selection matters more than decorative knots. In Australia, “cedar” may mean imported western red cedar or a locally grown timber sold under a trade name, so confirm the species, drying method and treatment at the timber yard. Poles sold as green or merely stacked for appearance are not ready for fine joinery.

A clean design uses two straight poles, four horizontal rails and discreet black fixings. Broad spacing lets a folded quilt sit without bunching, while a slight backward lean gives the piece a relaxed appearance. It is a build that rewards careful layout, simple tools and patience between machining and assembly.

Outdoor conditions set the standard in Australia: strong UV, summer heat, coastal salt and heavy rain can punish a neglected finish. Metric hardware is easy to source at Bunnings, yet the timber deserves better treatment than a quick coat of varnish. Plan for a ladder that can be moved, wiped down and maintained.

Choosing suitable cedar poles

Choose poles with a gradual taper, a straight centreline and few deep splits. A string line or straightedge can reveal a bow greater than about 15 millimetres over 2.4 metres. Shallow surface checks are acceptable, but reject timber with rot, soft patches, active insect damage or splits running through the centre.

For adjacent design cues, Cantolirico’s woodworking furniture ideas collection shows how simple timber forms can suit contemporary Australian interiors. Look for the same combination of strong proportions and restrained connections when judging the finished ladder.

Drying and dressing the timber

Store the poles horizontally under cover with evenly spaced stickers, allowing air to move around them. Avoid ground contact and sealed plastic, which can trap moisture. A calibrated moisture meter is useful, but allow the timber to reach a stable moisture level close to the conditions where it will be used before machining the joints.

Keep the working area organised, with ear protection, eye protection and a stable bench for crosscutting. If the build is happening away from mains power, test the site equipment before starting. That same checklist of weight, setup and weather resistance appears in this portable antenna field review, a useful parallel when selecting kit for an off-grid project.

Setting out a comfortable lean

Set the two poles at their intended angle before cutting any rails. A lean of 10 to 15 degrees from vertical looks relaxed while keeping the footprint manageable. Check that the finished piece will clear doors, skirting boards and nearby furniture throughout its full height.

Mark four rail positions along the poles, generally 280 to 320 millimetres apart. Work down from the highest rail so the spacing remains balanced, and check both the vertical and diagonal measurements. Label each rail and pole immediately, since the two sides should mirror one another without unnecessary trimming later.

Cutting and assembling the frame

Cut four rails from sound 45 by 20 millimetre hardwood or well-seasoned cedar. At each crossing, form a shallow housing in the rail and flatten a small seating area on the inner face of the pole. Trial-fit the joints before cutting the final tenons, then lock them with exterior-grade epoxy and centred hardwood dowels.

Clamp the assembly with padded clamps and check it diagonally as each joint is tightened. Avoid forcing mismatched timber into alignment, since excessive clamping can split the poles. The finished frame should resist twisting even before the fixings are fitted.

Related outdoor inspiration comes from this cedar pipe bar project, which pairs natural timber with robust metal details suited to an Australian garden setting.

Smoothing and protecting the finish

Round every exposed edge and sand the rails through progressively finer grades, finishing around 180 to 220 grit. Vacuum the dust thoroughly before applying a penetrating exterior oil in thin coats. Allow the first coat to soak into the cedar, remove the excess and apply a second coat, paying particular attention to the end grain.

Film-forming varnish tends to trap moisture and show scratches, whereas a maintained oil finish can be renewed without stripping the whole ladder. Cedar’s natural resistance to decay does not make it immune to termites, salt or prolonged dampness, so keep the feet clear of soil and inspect the finish each season.

Choosing hooks and fixings

A blanket ladder can remain completely hook-free because the fabric simply rests over the upper rail. Optional clips should be smooth, rounded and easy to remove; leather loops or blackened steel can create a more deliberate modern detail. Old turned fittings can provide a reference for small metal shapes, and this pipe collector’s resource is an unusual but visually rich source of such forms.

Use stainless-steel or hot-dip galvanised fixings near coastal homes, and pair bolts with broad washers to avoid crushing the timber. Metric M8 hardware suits most of the frame. Any wall restraint should include a slotted hole at the top so seasonal timber movement does not split the pole.

Placing and using the ladder

Position the feet on a level floor and fit non-slip pads beneath them. Check the ladder with the intended blankets hanging from it, watching for rocking or twisting at the joints. Unless the design has been independently engineered for access, treat it as a storage and display ladder rather than a step ladder.

If a mate offers to test it, have them load and pull the blankets rather than climb the rails. The rails should remain firm under sideways pressure, and the poles should not slide apart. Adjust the lean or tighten a fixing if either problem appears.

Keep the ladder away from wet garden soil, wipe coastal salt from the surface and inspect the fixings annually. Re-oil the timber when water stops beading on it. A well-fitted ladder should look relaxed in the room and behave like fixed joinery when the blankets are pulled.